 |
We supply our gun and weapon manufacturers the full range of custom fasteners, including custom screws/bolts, standoffs/spacers, springs, washers, nuts, pins, machined components, and much more. We are proud to serve a small but critical part with many specialized gun and accessory manufacturers across the nation including SCCY, Christensen Arms, Royal Arms, and Connectec to name a few.
CALL US WITH YOUR INQUIRIES AT (866) 243-3044 OR EMAIL US AT [email protected]
|
|
-
Tight tolerances were required on these 4140 steel precision nuts, with most dimensions at +.000/-.005 or +.000/-.003 inches. Overall thickness of the nut was set at .155" and 10-24 class 2B thread tapped all the way through. Full production of this part was at 20,000 pieces and lead time at approximately 75-90 days from order confirmation.
-
These are custom 6-lobe socket cap screws made domestically using 4037 alloy steel material. Strength was absolutely critical to our customer and the parts were heat treated to 39-43 hrc. In the absence of an available drawing for this part we had to work off samples our customer provided for all dimensional attributes. After confirming the material, strength, and dimensional requirements we had 1,000 pcs produced for our customer with a lead time of approximately 12 weeks from order confirmation. Heat treat and material certs were included with the parts.
-
These custom 6-lobe socket head screws were manufactured domestically using 4140 alloy steel material with heat treat to 42-47 HRC. 2A 6-48 UNS thread was incorporated with thread length at .375". T15 6-lobe drive was cold formed and the thread rolled.
-
Approximately 34,000 pieces of these custom bead blast flat socket screws were supplied to our customer in the weapons & gun manufacturing sector. Half the parts were set at 1.29" length while the other half set to 1.695" length. The same 1/4-28 thread was incorporated on both parts and the socket drive was cold headed. A spherical readius shape was incorporated into the top of the flat head, which is difficult to discern in the photos shown. The head height measured .097" and the head diameter at .375". Glass bead blast process was used to add the matte sand finish desired by our customer.
-
These custom class 10.9 socket head bolts were manufactured for our gun accessory manufacturing customer with commercial black oxide finish. The rolled #6-48 thread length was set to 3.5MM +/-0.3MM and the head height to 2.28MM +/-0.2MM. Head diameter measured at 5.05MM +/-0.12MM with a cold formed 2.38-2.41MM hex socket drive.
-
We get these custom cold headed screws with black nitride finish manufactured 100% domestically for our gun manufacturing customer using 302 stainless steel material. 1/4-28 partial thread is rolled to .75" in length and overall length is set to 1.695". Black nitride finish was added at 980 to 1050 degrees and effective case thickness of .0005 to .0020".
-
These custom extended dog point set screws were manufactured using 4140 alloy steel material with zinc clear finish. 6-32 thread was rolled at .150" in length and a 1/16" hex socket drive was incorporated. Overall length measured .45" and the dog point diameter was set to .097 +/- .001".
-
These are custom flat socket head cap screws manufactured domestically using 18-8 stainless steel material. The production run was relatively low in quantity at approximately 10,000 pcs, with a standard non-expedited lead time of 6-7 weeks. Material certs, certificate of conformance, and passivation certs to QQ-P-35 were provided with the parts.
-
These custom flat socket head screws were manufactured domestically at 20,000 pieces in the 1.695" overall length and the same quantity in 1.29" overall length. 302 stainless steel material was used with plain passivated finish. Head diameter was .375" and head height at .097", with a 90 degree countersunk base. Partial thread of .75" was rolled for both length variations. Material certs and certificate of conformance was provided with the parts.
-
These custom internally threaded stainless steel ball studs were manufactured using 303 stainless steel material with 12-40 internal thread inside the ball stud and also 10-24 external thread rolled on the male portion. Three different length variations on the male thread length were produced per our customer's requirements.
-
These custom low profile socket head screws with a 6-lobe (torx) drive were manufactured domestically using 302 stainless steel material with a commercial passivated plain finish. 5,000 pieces of two sizes were produced: M10 - 1.5M X 65MM with a T-45 drive size and M8 - 1.25M X 65MM with a T-30 drive size. 26-30MM of thread was incorporated on the larger version and 22-25MM on the smaller diameter part. The low profile & 6-lobe drive combination is relatively tricky, especially for these larger diameters as additional controls in tooling are required to avoid flowering on the outside profile of the head.
-
These custom low profile socket head screws were manufactured using 304 stainless steel material for our gun product manufacturing customer and were also provided with black oxide finish. Full 10-32 thread was rolled at a length of .75" below the cold forged head. Parts were provided with full certs per our customer's requirements.
-
These custom precision adapter dowel pins were manufactured for our defense customer using 4140 alloy steel material with Rc 38-42 hardness with plain finish. Production was done in the USA and the pins measured .10800" +/- .00025" in diameter and .375" +/-.010" in overall length. Full certs were provided with the parts per customer's instructions.
-
We had 1,000 pieces of these custom precision machined components manufactured domestically in the USA to serve as housing parts in a defense article production application. Aluminum alloy 2011 (Temper T3) material was used for the production and the parts were set for MIL-STD-171 compliant black dye. Dimensional requirement were fairly precise with tolerance at +.000/-.001 for most specifications.
-
These custom 303 stainless steel round dowel pins were manufactured domestically for our gun manufacturing customer. The OD was set to .1874-.1876 and overall length to .430 +/-.001. R.093 radius was incorporated on one side and commercial passivation was used as the last step to complete the parts for shipment.
-
We had approximately 120,000 pieces of these custom shoulder bolts manufactured domestically in the USA for our gun manufacturing customer. The shoulder measured .185 X 1/2 and 8-32 thread was rolled. To save on cost we incorporated a convex relief underneath the head in leu of a machined relief, allowing us to complete the entire head portion with cold heading. The shoulder was centerless ground to a +/-.001 diameter tolerance and we also made sure to meet the .127/.125 across flats requirement on the 1/8 hex socket drive, which was a critical feature for optimal key engagement.
-
We had 8 different configurations of these custom silicon bronze sleeve bearings manufactured domestically for our defense customer. Production was done domestically in the USA and full certs were available upon request.
-
These custom torx 6-48 socket head cap screws were manufactured domestically using 4140 alloy steel material with heat treat to 42-47 HRC. 2A 6-48 UNS thread was incorporated with thread length at .200". T15 6-lobe drive was cold formed and the thread rolled.
-
We provided our gun manufacturing customer these custom torx drive socket head bolts per print using 416 stainless steel material heat treated to HRC 36-44. Approximately 13.8MM of 1/4-28 2A thread was rolled on both the 34.31MM and 43.61MM overall length version we had manufactured and the unthreaded shoulder diameter was set to 6.35MM +.00/-.22MM. The head profile and countersink was customized to our customer's specifications.
|
